Download or view screwThreadsTest.frink in plain text format
/** This is a test of the screwThreads.frink library to make screw threads for
3-d printing.
This test creates a male and female garden hose fitting with threads
as defined by the standard ASME B1.20.8-1991 (reaffirmed 1998).
*/
use screwThreads.frink
res = 254/inch
pitch = inch/11.5
//minorRadius = 0.9495 in / 2
threadHeight = .05648 in
// Male minor radius. This is the average of the allowed min and max pitch
// diameter (table 2) minus half the thread height.
minorRadius = (1.0060+0.9975) in /2 / 2 - threadHeight/2
turns = 4.25
pilot = 1/8 in - pitch/2
// Female major radius
// This is the average of the allowed min and max pitch
// diameter (table 3) minus half the thread height.
femaleRadius = (1.0160 + 1.0245) in / 2 / 2 - threadHeight/2
println["threadHeight is " + format[threadHeight, "mm", 2]]
println["minorDiameter is " + format[2 minorRadius, "in", 4]]
println["majorDiameter is " + format[2 minorRadius + 2 threadHeight, "in", 4]]
println["femaleDiameter is " + format[2 femaleRadius + 2 threadHeight, "in", 4]]
println["gap is " + format[femaleRadius - minorRadius, "mm", 2]]
tool = makeDoubleConeTool[pitch/2, threadHeight, res]
maleThread = makeThreads[minorRadius, pitch, 0 deg, turns * 2 pi, 0, tool, res]
malePipeOuter = callJava["frink.graphics.VoxelArray", "makeCylinder", [0,0,-1/4 in res,0,0,(turns pitch + pilot) res, minorRadius res]]
malePipeInner = callJava["frink.graphics.VoxelArray", "makeCylinder", [0,0,-1/4 in res,0,0,(turns pitch + pilot) res, (minorRadius-2.4 mm) res]]
male = maleThread.union[malePipeOuter]
male.remove[malePipeInner]
femaleThread = makeThreads[femaleRadius, pitch, 0 deg, (turns+1) * 2 pi, 0, tool, res]
femalePipeOuter = callJava["frink.graphics.VoxelArray", "makeCylinder", [0,0,-1/4 in res,0,0,(turns pitch) res, (femaleRadius + 2.4 mm) res]]
femalePipeInner = callJava["frink.graphics.VoxelArray", "makeCylinder", [0,0,-1/4 in res,0,0,(turns pitch) res, femaleRadius res]]
femalePipeOuter.remove[femalePipeInner]
femalePipeOuter.remove[femaleThread]
female = femalePipeOuter
male.projectX[undef].show["X"]
male.projectY[undef].show["Y"]
male.projectZ[undef].show["Z"]
female.projectX[undef].show["X"]
female.projectY[undef].show["Y"]
female.projectZ[undef].show["Z"]
filename = "screwThreadsMale.obj"
print["Writing $filename..."]
w = new Writer[filename]
w.println[male.toObjFormat["male", 1/(res mm)]]
w.close[]
println["done."]
filename = "screwThreadsFemale.obj"
print["Writing $filename..."]
w = new Writer[filename]
w.println[female.toObjFormat["female", 1/(res mm)]]
w.close[]
println["done."]
Download or view screwThreadsTest.frink in plain text format
This is a program written in the programming language Frink.
For more information, view the Frink
Documentation or see More Sample Frink Programs.
Alan Eliasen was born 20217 days, 23 hours, 29 minutes ago.